G7200 Battery Charger

NOCO Genius G7200 Trickle Battery Charger

The G7200 is a smart, 12 Step, fully automatic switch-mode battery charger and maintainer. The G7200 restores batteries to their original capacity, recovers slightly sulfated batteries, charges batteries in cold climates, rescues drained batteries, and provides maintenance charging to increase battery life. A powerful battery charger with specialized charging modes for recovering severely drained batteries that will not accept a normal charge. Suitable for most 12V and 24V battery capacities from 14-230Ah, such as Motorcycles, ATVs, UTVs, Snowmobiles, Jet Skis, Cars, RVs, Boats and Trucks.

Twelve Step Battery Charging

Step 1: Diagnostics
Checks the battery voltage to make sure battery connections are good and the battery is in a stable condition before beginning the charge process.

Step 2: Recovery
Initializes the Recovery process, if needed, for deeply discharged or sulfated (desulfation) batteries by pulsing small amounts of current.

Step 3: Soft Start
Begins Bulk charging process with a gentle (soft) charge.

Step 4-7: Bulk
The Bulk charging process continues using Max Rate, High Rate, Medium Rate and Low Rate charges and returns 80% of battery capacity, indicated by the 25%, 50% and 75% CHARGE LEDs.

Step 8: Absorption
Brings the charge level to 90%. The battery charger will deliver small amounts of current to provide a safe, efficient charge and limit battery gassing.

Step 9: Trickle
Battery is fully charged and ready to use, indicated by the 100% CHARGE LED being a solid Green. In this step, the battery charger will only deliver enough current to keep the battery full. If the battery tells the charger that more current is needed, the battery charger will switch to Maintenance.

Step 10: Maintenance
Continuously monitors the battery voltage to determine if a Maintenance charge should be initiated. If the terminal voltage falls below 12.8V (12V) and 25.6V (24V), the charger will start the Maintenance cycle until voltage reaches 14.4V (12V) and 28.8V (24V) and then discontinues the charge cycle. The cycle between Trickle and Maintenance is repeated indefinitely to keep the battery at full charge, without overcharging. The battery charger can be left connected indefinitely.

Step 11: 13.6V Supply
The 13.6V SUPPLY mode is used for low voltage batteries, maintenance charging or as a power supply.

Step 12: 16V Boost
The 16V BOOST mode is used to recover battery capacity from a stratified (sulfated) battery by applying a specialized high 16.5V (17V Max) voltage to soften and melt down sulfate from the battery plates so that the material becomes usable again.

Designed Tough

COMFORT CABLE CLAMPS

Ergonomically designed to make battery connecting and disconnecting effortless. Features a fully insulated over-mold casing with strain relief ends to alleviate unwanted tension on cable leads.

Connecting and disconnecting accessory leads has never been easier! A uniquely designed interchangeable connector allows accessories to be properly mated and fastened with a snap-lock latch.

BUILT-IN FUSE PROTECTION

 

Each battery connection accessory features an over-molded inline fuse to increase user safety by protecting the battery charger from potentially dangerous short circuits.

RUGGED ENCLOSURE

Made from a rugged polymer for high-impact resistance for some of the harshest and most demanding working environments.    

     WHAT'S IN THE BOX

• G7200 Charger
• Battery Clamp Connectors
• Eyelet Terminal Connectors
• Owner's Manual & User Guide
• Product Registration Card

CHARGING TIMES The time required for the G7200 to charge a normally discharged battery is shown below. Deeply discharged batteries may take longer to charge depending on the depth of discharge (DOD). The charge time is based on an average depth of discharge to a fully charged battery. Note: The above table is for reference purposes only. Actual data may differ due to battery conditions. The time required for the G7200 to charge a normally discharged battery is based on an average DOD of 50%.     G7200 TECHNICAL SPECIFICATIONS Input Voltage AC 110-120 VAC, 50-60Hz Working Voltage AC 85-130 VAC, 50-60Hz Input Current 2000mA RMS Max Efficiency 85% Approx. Power 150W Max Charging Voltage 14.4/28.8V, 14.7/29.4V (Cold/AGM), 13.6V (Supply), 16.5V (Boost) Charging Current 7200mA (12V), 3600mA (24V), 5000mA (Supply), 1500mA (Boost) Back Current Drain <5mA Ripple <2% Ambient Temperature 0°C to +40°C Charger Type 12 Step, Fully Automatic, Switch-Mode Type of Batteries 12V & 24V Lead-Acid Battery Chemistries Wet, Gel, MF & AGM Battery Capacity 14-230Ah (12V), 14-120Ah (24V), Maintains All Battery Sizes Housing Protection IP65 Cooling Natural Convection Noise Level <50dB Dimensions (L x W x H) 8.9 x 3.8 x 2.4 Inches Weight 1.7 Pounds