Call Us: 888-631-1433
COUPON CODES     SCP5: $5 OFF ORDERS OVER $125    SCP25: $25 OFF ORDERS OVER $275   SCP50 $50 OFF ORDERS OVER $550
Painted Parts are painted to order and take additional time, right now we are about a 4-5 week lead time. Please keep this in mind.
Nissan 350Z Billet Aluminum Machined Racing Pedal Set
  • Free shipping

        Nissan 350Z Billet Aluminum Machined Racing Pedal Set

        Nissan 350Z Billet Pedal Set

        CNC Machined from Aircraft Quality Billet Aluminum Racing Pedal Set for the Nissan 350Z

        These racing pedals, designed and manufactured for the Nissan 350Z, are made from CNC Machined aircraft quality billet aluminum, and anodized and machined for the ultimate style and finish. Available in multiple different machined finishes and anodized color finishes, these pedals equate to the ultimate in both style and function. Machined for ultimate grip, and designed for a premium race-car like shifting experience, these pedal sets are designed to improve the racing drivability of your 350Z while also giving it a fantastic interior finish and appearance.

        Aluminum Billet Automatic Transmission Machined Racing Pedals for the Nissan 350Z

        350Z Manual Transmission Billet Aluminum Racing Pedal Set

        Available in the following machined finish options: Grid and Block Style

        Block Machined Finish for the SRP Racing Pedals SetGrid Machined Finish for the Camaro Racing Pedal Sets

         

        Anodizing options are also available. You can order your pedal set without color anodizing, or with black/Silver anodizing.

        Nissan 350Z Racing Pedals

        Available for both the Manual and Automatic Transmission 350Z.

        Both kits come with Dead Pedal.

         

        FREE SHIPPING to the Continental 48 States!

        Because of the custom nature of these pedals, production time can sometimes run 3-4 weeks and up. Please allow this lead time before shipping.

        Install Information:

        When installing our pedals you do have to drill holes into your factory pedals.  Once installed, our pedals are a part of your car with no chance of coming off.  All hardware is stainless steel and provided.  The instructions below are applicable to most cars.  However, some cars will have a slightly different installation procedure.  These differences should be noted on the pedal page for the vehicle.  The typical installation time is 30 minutes to 1 hour.  Your results may vary.  If you ever decide to remove your SRP pedals, the factory rubber covers can be put back on the brake and clutch to cover the holes.  The holes you drill into the gas pedal and footrest are really small enough to not be noticed, unless looked at closely.
         
        Tools required:
        Drill - 3/16" drill bit
        Phillips head screwdriver - 1/16" drill bit
        9mm wrench - Center punch

        Warning:  Make sure you wear safety glasses during this installation.
         
        1. Remove any factory rubber or factory metal/plastic sport covers or any other aftermarket pedal covers from the brake, clutch and/or gas pedal when and if applicable.  Most factory rubber covers will pull right off.  Some factory metal/plastic sport pedal covers have rivets which must be drilled out (do not drill thru pedal yet) with a 1/8” drill bit to remove the cover.


        2.  Put masking tape on the brake and clutch and mark the mounting holes using the aluminum pedals as a template.  Make note of where the rod is welded to the back side of the pedal pad in relationship to the holes in the billet cover. Align the billet covers in such a way that after you drill through the pedals there will be room to install and hold the nuts on the back side of the pedals.


        3.  Use your center punch and hammer and punch your mounting holes marked on the brake and clutch.  Use the 1/16” drill bit to drill pilot holes, followed by the 3/16” bit.  Mount the brake and clutch using machine screws and lock nuts.


        4.  Put masking tape and the gas pedal and footrest.  Using the aluminum cover, mark your mounting holes.  Remove aluminum cover.  Drill pilot holes with 1/16” drill bit.  Tap the holes with the pointy self tapping screws.  Remove screws, put pedal into position, and attach using self tapping screws.
         
        ·Check that all pedals are securely attached using all mounting locations.

        ·Make sure all pedals have adequate clearance between adjacent pedals and floor covering.  

        ·After driving, recheck all pedals to make sure they are secure.

        ·NOTE:  the gas pedal is typically smooth so that your foot will slide across it. 

        0.0
          • 36% less
          Market price: $139.99, you save $50.99
        • $89.00

        OR
          • SKU
            SRP350ZPedal
          • Weight
            12 lbs
        • Disallow Use of Coupons
          No
        • Finish
          Grid Style Machined Finish, Block Style Machined Finish
        • Anodizing
          Black and Silver Anodizing, No Anodizing
        • Options
          Automatic, Manual
        Customer reviews
        Please sign in to add review
        There are no comments yet. Be the first to leave a comment

        We accept the following payment methods:

        Accepted payment methods

        Shipping

        We utilize UPS, Fedex, and USPS for all of our shipping needs. Carrier choice is based upon availability and needs of the customer and is the sole discretion of SouthernCarParts. We always try to ship within 24 hours of order placement (do to the custom nature of some products, shipping within 24 hours is impossible, actual shipping time frames will be listed in the product description). Please keep in mind that some products such as Custom Fit Car Covers, Lloyds Floor Mats, Painted accessories, and Racemesh Products can take 3 -10 days to ship and are charged at time of order placement. Racemesh products take 4 weeks to ship as they are made to order.

        Returns


        Should you need to return a part for refund, exchange, or credit, please contact our returns department within 30 days of purchase at orders@southerncarparts.com for a Return Merchandise Authorization (RMA) number. Most problems, such as installation, can be solved with a telephone call (888-631-1433). Southern Car Parts will not accept returned goods without prior authorization and an RMA# written clearly on the exterior of the box. The customer is responsible for freight on all return orders. Parts authorized to be returned, on a non-exchange basis, are subject to a 20% restocking fee. Returns will only be accepted within 30 days of the original date of shipment.  Custom painted parts - Once these parts are started, we can refund you less the paint(chemicals) that have been used. Exception is rear spoilers and front splitters, we can refund less 20%.

        Custom-made-to-order items are NOT returnable. This includes embroidered floor mats and car covers.
        Damages in Shipping

        All damages from shipping must be reported to Southern Car Parts within two business days from tracking number delivery confirmation. After two business days, damages become the responsibility of the customer.