Shop By
Currently Shopping by:
- Remove This Item Manufacturer: Wilwood Brakes
Filter
Wilwood Brakes
8 Item(s)
-
C6 Corvette Wilwood Front Big Brake Kit
Free ShippingW6A Wilwood Big Brake Front Brake Kit Pistons: 6 Rotor Diameter:14.25 Caliper Mount: Radial Min. Wheel Diameter: 18Compatible with the Chevrolet Chevrolet C6 Corvette 2010-2011 Cadilac XLR 2005-2009 All Chevrolet Chevrolet C6 Corvette C-5 1997-2004 All C-5 & ZO6 Chevrolet Chevrolet C6 Corvette C-6 2005-2009 All C-6 & ZO6 The C6 Corvette engineers were developing more horsepower out of the new LS engines in 2005, so they wanted to build the ultimate C6 Corvette. The Previous generation C6 Corvette grew in size and weight, so they wanted to make the new C6 Corvette smaller and lighter. The body was redesigned with exposed headlights to remove the weight involved in building a hideaway headlight system. Engine power was also increased to 400 horsepower, the same as the previous years Z06. The new Z06 horsepower was increased to 505 and the ZR1 C6 Corvette would have over 600 horsepower. Obviously, all of the new C6 Corvettes are performers so Wilwood offers several brake improvement kits. If you track your C6 Corvette, Wilwood offers a W6A Big Brake Front Brake Kit (Race) and a matching rear kit. This system can withstand the rigors of heavy track action. Increased braking for the street and track can be obtained with the Superlite 6R Big Brake Front Brake Kit with 13.06 or 14-inch rotors. Matching rear brakes with Superlite 4R calipers are also available. Wilwood also offers high-performance brake pads for the original C6 Corvette calipers and they provide a substantial brake improvement. Wilwood W6AR calipers were designed for the specific purpose of providing big capacity braking with large diameter rotors for heavy weight and extreme duty vehicles. For cars, it’s the biggest of the big providing big brake performance for show and dual purpose street and track vehicles. For trucks and SUV’s, it provides big stopping power for towing, off-road, and enhanced braking with a wheel and tire upgrades. Kits listed for specific vehicles are fully compatible with OE master cylinder output and ABS function. Directional staggered vane 14.25” rotors provide maximum cooling for sustained high heat durability. Calipers W6A Radial Mount The W6A forged six-piston caliper delivers heavy duty stopping power for the road or track. The caliper incorporates race technology into a body design with widespread adaptability. Radial mounting, two options for piston volume, and a rotor diameter ranging from 12.19" to 14.25" give this caliper the versatility necessary to suit all types of heavyweight braking requirements. The W6A body is the product of FEA computer design and stress flow forging technology. FEA technology allows the designer to test the prototype in a computer environment to determine the optimal structural design within the dimensional parameters of the component. Stress flow forging produces a part with the internal grain structure of the metal aligned in the direction of the flow of the body contour. The results are a caliper with superior clamping efficiency and ultimate strength against fatigue, stresses, and distortion under load. This caliper generates big brake clamping force with six differential bore stainless steel pistons. Stainless steel is used for its high resistance to corrosion and low thermal conductivity that reduces the heat transfer from the pads. The differential bore pattern balances pad loading to help maintain even pad wear. High-temperature bore seals provide long service life and maintain their resilience to provide positive piston retraction on release. Two options for overall piston volume make it simple to match the calipers with master cylinder output and rear caliper size for correct bias proportioning. The performance of the W6A is enhanced with SRS bridge plates, snap-ring locked pad retainer pins, recessed two-piece bleed screw assemblies and dampen mounted fluid transfer tubes. SRS bridge plates eliminate all bridge wear caused by pad gouging. The spring-loaded action of the plates also eliminates pad rattle. Snap ring clips lock the pad pins in place to provide positive retention and allow easy service without caliper removal. The bleed screws are recess mounted for protection against impact and debris. The fluid tubes are dampen mounted to protect them from fatigue or damage from vibration or debris. Calipers are anodized in high luster black to protect from corrosion and maintain their high-tech appearance. The W6A is also available with a gloss red finish or other custom Wilwood color by order. Radial-mount adapter brackets are used in Wilwood brake kits to provide a secure and precise method of attaching the W6A caliper to the factory mount bosses on the original spindle. Rotors SRP Drilled Performance Rotor SRP Drilled Performance Rotors feature a specially engineered directional cross drill and face slot pattern that improve brake response and pad performance throughout the entire range of light to heavy braking. The venting and cleaning action of the holes and slots will reduce pad glaze and disperse gasses and heat generated during the pad to rotor interface. The holes and slots also inhibit irregular pad compound build-up on the rotor faces resulting in smoother engagement and improved pedal response in all conditions. The material removed also contributes to lower rotating and unsprung suspension weight. Along with the excellent performance characteristics of this rotor design, each rotor is treated with a black electro-coat to inhibit corrosion on all areas of the rotor. The high tech design, classic style, and aesthetic appeal of the SRP series are the perfect finishing touches to any wheel and tire detail. SRP rotors are available in all popular sizes used in Wilwood's Pro Series and Big Brake conversion kits. Kits in these categories designated with the drilled rotor option get the SRP as standard equipment. Rotor Hats Big Brake - Short Offset GT Series Big Brake Short Offset hats are precision machined from premium aluminum alloys for high strength and attention to minimized weight. Hats in this category feature threaded rotor mount holes for use with standard through-hole mount rotors. Threaded hole hats may also be used with T-Nuts or bobbins designed for use with specially machined slotted hole dynamic mount rotors. When used in conjunction with matched Wilwood rotor hardware kits, GT hats provide solid, reliable performance in the most demanding conditions. Short Offset Hats are for narrow space applications with offsets often less than 1.00". They are available for most rotor bolt patterns in a variety of four and five lug wheel patterns. Shallow Offset Hats are for narrow space applications with offsets often less than 1.00". They are available for most rotor bolt patterns in a variety of four and five lug wheel patterns. Check clearance diagram below to ensure proper fitment with your wheel application. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette, Z06 . -
2008-2019 Wilwood Challenger Rear Big Brake Kit
Free ShippingSuperlite 4R Challenger Big Brake Rear Brake Kit For OE Parking Brake Pistons: 4 Rotor | Diameter:14 | Caliper Mount:Radial | Min. Wheel Diameter: 18 Compatible with: 2008+ Dodge Challenger - All Models The Challenger engineers developed a vehicle, which was released to the public in 2008 with tremendous fanfair and popularity, that is an absolute monster. The Previous generation Challenger hadn't been produced in years, so Dodge went back to the drawing board and released a gorgeous and powerful vehicle that has been turning heads since it hit the market. Three models of the Challenger were released. The SE V6 Challenger, while underpowered compared to its other model brethren, is still a beast of a vehicle with a powerful and capable engine that could benefit from increased stopping power, since it has the ability to get to speed so easily. The Hemi R/T and SRT-8 Challenger models, on the other hand, are anything but underpowered. Those high HP monster machines can really get moving, and high performance brakes from Wilwood are the perfect complimentary accessory to bring the big beast to a stop quickly and smoothly. These Wilwood Big Brake kits come in various different applications to match the performance style needs of your Challenger, and being that they're Wilwood, you can be absolutely certain that you are getting the very best for your dollar. Wilwood has been tearing up the performance brake scene for some time now, and the reviews for their products are universally outstanding. Billet Superlite 4R four piston calipers are combined with BP-10 compound pads and 13”-14” rotors in this group of big brake kits for custom high performance street and show machines. This group of specialized kits for cars, trucks, and SUV’s retain full use of the OE parking brake, master cylinder output, and ABS where used. SL4R rear kits provide complimentary style and performance with 13” and larger front brake upgrades in conjunction with wheel, tire, and suspension upgrades. Optional caliper finishes and rotor designs enable the builder to match style and performance on all applications. Calipers Billet Narrow Superlite 4 The Superlite caliper series has set the standard for many years in short track, late model, modified and open wheel competition. It has also enjoyed prominence in a variety of road-race, off-road, rally and sport driving applications. Starting at 4.40 pounds, the Forged Billet Superlite (FSL) is the newest innovation to this series from Wilwood. New and adaptive technologies have been applied providing substantial improvements in strength, fluid volume displacement, and overall performance. The Superlite caliper series has set the standard for many years in short track, late model, modified and open wheel competition. It has also enjoyed prominence in a variety of road-race, off-road, rally and sport driving applications. Starting at 4.40 pounds, the Forged Billet Superlite (FSL) is the newest innovation to this series from Wilwood. New and adaptive technologies have been applied providing substantial improvements in strength, fluid volume displacement, and overall performance. The FSL body design is a highly efficient product of computer generated solid modeling and stress analysis technology. Each caliper features closed end bridges with a radial transition to the piston body housings. The elimination of machined steps and sharp shoulders in this critical area provides a measurable increase in overall body strength and resistance to deflection under load. Center bridge bolts replace cotter pins to provide additional support and allow quick access with positive brake pad retention. Clamping force, structural deflection, and volume displacement tests have proven the superior strength and efficiency of the FSL. On-track testing has proven driver satisfaction. The bottom line is better stopping power with less pedal travel. The superior strength of this innovative new caliper is combined with proven performance features from other Wilwood designs. Each caliper is equipped with Wilwood's replaceable SRS stainless steel bridge plates. SRS plates eliminate the bridge wear caused by pad gouging and extend the service life of the caliper body. The spring-loading action of the SRS plates also eliminates pad rattle and dampens the vibration harmonics that contribute to squeal under braking. Other standard Wilwood features include high-temperature, square faced o-ring seals for positive sealing, controlled piston retraction, and long service life in high heat conditions. Stainless steel pistons are used to resist corrosion and retard heat transfer from the pads. Fluid tubes are vibration dampened to resist stress fractures and reduce damage caused by track debris. Two-piece bleed screw assemblies provide long, reliable service life and are easily replaced if necessary. Forged Billet Superlite calipers are a direct replacement for all Wilwood Superlite and similar competitive brand calipers with 3.50" centered mounting tabs. Calipers are available in the popular 1.75", 1.62”, 1.38", 1.25” and 1.12” piston sizes for .81", 1.10" and 1.25" rotor widths. FSL calipers use the same 7420 type bridge bolt brake pad used in all Superlite 6 piston calipers. The full range of PolyMatrix pad compounds is available to match brake response and heat range to any application. Rotors GT-72 curved vane rotors are built for the extreme conditions of professional motorsports. The superior heat absorption and dissipation characteristics of these heavy wall directional vane rotors are the keys to preventing heat fade and realizing long service life from the rotors and pads. All rotors are cast from premium grade, long grain carbon iron for long wear, thermal stability, and resistance to distortion. Every GT rotor is fully detail machined to eliminate stress points and unnecessary weight away from the pad sweep face. The faces and O.D. are precision turned to less than .001" for flatness, parallelism, and run-out. An asymmetrical face slot pattern provides smoother engagement through reduced harmonics and improved thermal balance between the I.D. and O.D. of the rotor. Every rotor is then individually dynamic balanced to provide vibration free performance at any speed. These rotors provide the highest cooling capacity and longest service life for extreme braking short tracks and road course competition. Rotor Hats Parking Brake Hat - Standard These premium grade cast iron hats are used with Wilwood's internal shoe parking brake kits. Each hat is a precision machined, threaded hole design for use in conjunction with through-hole mount rotors. After machining, the hats are electro-coated for corrosion resistance. Check clearance diagram below to ensure proper fitment with your wheel application. Note(s): 1. 14" Rotor 2. Kit will require aftermarket wheel spacers of 1/8th" (not included in kit) for rear kit installation with OE wheels. -
C6 Corvette Wilwood Rear Big Brake Kit
Free ShippingSuperlite 4R C6 Corvette Big Brake Rear Brake Kit For OE Parking Brake Pistons: 4 Rotor Diameter:14 Caliper Mount: Radial Min. Wheel Diameter: 18 Compatible with Chevrolet C6 Corvette 2010-2011 Chevrolet C6 Corvette C-5 1997-2004 All C-5 & ZO6 Rear Disc Chevrolet C6 Corvette C-6 2005-2010 All Rear Disc The C6 Corvette engineers were developing more horsepower out of the new LS engines in 2005, so they wanted to build the ultimate C6 Corvette. The Previous generation C6 Corvette grew in size and weight, so they wanted to make the new C6 Corvette smaller and lighter. The body was redesigned with exposed headlights to remove the weight involved in building a hideaway headlight system. Engine power was also increased to 400 horsepower, the same as the previous years Z06. The new Z06 horsepower was increased to 505 and the ZR1 C6 Corvette would have over 600 horsepower. Obviously, all of the new C6 Corvettes are performers so Wilwood offers several brake improvement kits. If you track your C6 Corvette, Wilwood offers a W6A Big Brake Front Brake Kit (Race) and a matching rear kit. This system can withstand the rigors of heavy track action. Increased braking for the street and track can be obtained with the Superlite 6R Big Brake Front Brake Kit with 13.06 or 14-inch rotors. Matching rear brakes with Superlite 4R calipers are also available. Wilwood also offers high-performance brake pads for the original C6 Corvette calipers and they provide a substantial brake improvement. Billet Superlite 4R four piston calipers are combined with BP-10 compound pads and 13”-14” rotors in this group of big brake kits for custom high-performance street and show machines. This group of specialized kits for cars, trucks, and SUV’s retain full use of the OE parking brake, master cylinder output, and ABS where used. SL4R rear kits provide complimentary style and performance with 13” and larger front brake upgrades in conjunction with wheel, tire, and suspension upgrades. Optional caliper finishes and rotor designs enable the builder to match style and performance on all applications. Calipers Billet Narrow Superlite 4 The Superlite caliper series has set the standard for many years in short track, late model, modified and open wheel competition. It has also enjoyed prominence in a variety of road-race, off-road, rally and sport driving applications. Starting at 4.40 pounds, the Forged Billet Superlite (FSL) is the newest innovation in this series from Wilwood. New and adaptive technologies have been applied providing substantial improvements in strength, fluid volume displacement, and overall performance. The Superlite caliper series has set the standard for many years in short track, late model, modified and open wheel competition. It has also enjoyed prominence in a variety of road-race, off-road, rally and sport driving applications. Starting at 4.40 pounds, the Forged Billet Superlite (FSL) is the newest innovation in this series from Wilwood. New and adaptive technologies have been applied providing substantial improvements in strength, fluid volume displacement, and overall performance. The FSL body design is a highly efficient product of computer generated solid modeling and stress analysis technology. Each caliper features closed end bridges with a radial transition to the piston body housings. The elimination of machined steps and sharp shoulders in this critical area provides a measurable increase in overall body strength and resistance to deflection under load. Center bridge bolts replace cotter pins to provide additional support and allow quick access to positive brake pad retention. Clamping force, structural deflection, and volume displacement tests have proven the superior strength and efficiency of the FSL. On-track testing has proven driver satisfaction. The bottom line is better stopping power with less pedal travel. The superior strength of this innovative new caliper is combined with proven performance features from other Wilwood designs. Each caliper is equipped with Wilwood's replaceable SRS stainless steel bridge plates. SRS plates eliminate the bridge wear caused by pad gouging and extend the service life of the caliper body. The spring-loading action of the SRS plates also eliminates pad rattle and dampens the vibration harmonics that contribute to squeal under braking. Other standard Wilwood features include high-temperature, square-faced o-ring seals for positive sealing, controlled piston retraction, and long service life in high heat conditions. Stainless steel pistons are used to resist corrosion and retard heat transfer from the pads. Fluid tubes are vibration dampened to resist stress fractures and reduce damage caused by track debris. Two-piece bleed screw assemblies provide long, reliable service life and are easily replaced if necessary. Forged Billet Superlite calipers are a direct replacement for all Wilwood Superlite and similar competitive brand calipers with 3.50" centered mounting tabs. Calipers are available in the popular 1.75", 1.62”, 1.38", 1.25” and 1.12” piston sizes for .81", 1.10" and 1.25" rotor widths. FSL calipers use the same 7420 type bridge bolt brake pad used in all Superlite 6 piston calipers. The full range of PolyMatrix pad compounds is available to match brake response and heat range to any application. Rotors GT-72 curved vane rotors are built for the extreme conditions of professional motorsports. The superior heat absorption and dissipation characteristics of these heavy wall directional vane rotors are the keys to preventing heat fade and realizing long service life from the rotors and pads. All rotors are cast from premium grade, long grain carbon iron for long wear, thermal stability, and resistance to distortion. Every GT rotor is fully detail machined to eliminate stress points and unnecessary weight away from the pad sweep face. The faces and O.D. are precision turned to less than .001" for flatness, parallelism, and run-out. An asymmetrical face slot pattern provides smoother engagement through reduced harmonics and improved thermal balance between the I.D. and O.D. of the rotor. Every rotor is then individually dynamic balanced to provide vibration free performance at any speed. These rotors provide the highest cooling capacity and longest service life for extreme braking short tracks and road course competition. Rotor HatsParking Brake Hat - Standard These premium grade cast iron hats are used with Wilwood's internal shoe parking brake kits. Each hat is a precision machined, threaded hole design for use in conjunction with through-hole mount rotors. After machining, the hats are electro-coated for corrosion resistance.Check clearance diagram below to ensure proper fitment with your wheel application. Note(s): 1. 14" Rotor 2. The kit will require aftermarket wheel spacers of 1/8th" (not included in kit) for rear kit installation with OE wheels. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette, Z06 . -
2008-2021 Wilwood Challenger Front Big Brake Kit
Free ShippingW6A Wilwood Big Brake Front Brake Kit Pistons: 6 Rotor | Diameter:14.25 | Caliper Mount:Radial | Min. Wheel Diameter: 18Compatible with the: 2008+ Dodge Challenger - All Models The Challenger engineers developed a vehicle, which was released to the public in 2008 with tremendous fanfair and popularity, that is an absolute monster. The Previous generation Challenger hadn't been produced in years, so Dodge went back to the drawing board and released a gorgeous and powerful vehicle that has been turning heads since it hit the market. Three models of the Challenger were released. The SE V6 Challenger, while underpowered compared to its other model brethren, is still a beast of a vehicle with a powerful and capable engine that could benefit from increased stopping power, since it has the ability to get to speed so easily. The Hemi R/T and SRT-8 Challenger models, on the other hand, are anything but underpowered. Those high HP monster machines can really get moving, and high performance brakes from Wilwood are the perfect complimentary accessory to bring the big beast to a stop quickly and smoothly. These Wilwood Big Brake kits come in various different applications to match the performance style needs of your Challenger, and being that they're Wilwood, you can be absolutely certain that you are getting the very best for your dollar. Wilwood has been tearing up the performance brake scene for some time now, and the reviews for their products are universally outstanding.Wilwood W6AR calipers were designed for the specific purpose of providing big capacity braking with large diameter rotors for heavy weight and extreme duty vehicles. For cars, it’s the biggest of the big providing big brake performance for show and dual purpose street and track vehicles. For trucks and SUV’s, it provides big stopping power for towing, off-road, and enhanced braking with wheel and tire upgrades. Kits listed for specific vehicles are fully compatible with OE master cylinder output and ABS function. Directional staggered vane 14.25” rotors provide maximum cooling for sustained high heat durability. Calipers W6A Radial Mount The W6A forged six piston caliper delivers heavy duty stopping power for the road or track. The caliper incorporates race technology into a body design with widespread adaptability. Radial mounting, two options for piston volume, and a rotor diameter ranging from 12.19" to 14.25" give this caliper the versatility necessary to suit all types of heavy weight braking requirements. The W6A body is the product of FEA computer design and stress flow forging technology. FEA technology allows the designer to test the prototype in a computer environment to determine the optimal structural design within the dimensional parameters of the component. Stress flow forging produces a part with the internal grain structure of the metal aligned in the direction of the flow of the body contour. The results are a caliper with superior clamping efficiency and ultimate strength against fatigue, stresses, and distortion under load. This caliper generates big brake clamping force with six differential bore stainless steel pistons. Stainless steel is used for its high resistance to corrosion and low thermal conductivity that reduces the heat transfer from the pads. The differential bore pattern balances pad loading to help maintain even pad wear. High temperature bore seals provide long service life and maintain their resilience to provide positive piston retraction on release. Two options for overall piston volume make it simple to match the calipers with master cylinder output and rear caliper size for correct bias proportioning. The performance of the W6A is enhanced with SRS bridge plates, snap-ring locked pad retainer pins, recessed two-piece bleed screw assemblies and dampen mounted fluid transfer tubes. SRS bridge plates eliminate all bridge wear caused by pad gouging. The spring-loaded action of the plates also eliminates pad rattle. Snap ring clips lock the pad pins in place to provide positive retention and allow easy service without caliper removal. The bleed screws are recess mounted for protection against impact and debris. The fluid tubes are dampen mounted to protect them from fatigue or damage from vibration or debris. Calipers are anodized in high luster black to protect from corrosion and maintain their high-tech appearance. The W6A is also available with a gloss red finish or other custom Wilwood color by order. Radial mount adapter brackets are used in Wilwood brake kits to provide a secure and precise method of attaching the W6A caliper to the factory mount bosses on the original spindle. Rotors SRP Drilled Performance Rotor SRP Drilled Performance Rotors feature a specially engineered directional cross drill and face slot pattern that improve brake response and pad performance throughout the entire range of light to heavy braking. The venting and cleaning action of the holes and slots will reduce pad glaze and disperse gasses and heat generated during the pad to rotor interface. The holes and slots also inhibit irregular pad compound build-up on the rotor faces resulting in smoother engagement and improved pedal response in all conditions. The material removed also contributes to lower rotating and unsprung suspension weight. Along with the excellent performance characteristics of this rotor design, each rotor is treated with a black electro coat to inhibit corrosion on all areas of the rotor. The high tech design, classic style, and aesthetic appeal of the SRP series are the perfect finishing touches to any wheel and tire detail. SRP rotors are available in all popular sizes used in Wilwood's Pro Series and Big Brake conversion kits. Kits in these categories designated with the drilled rotor option get the SRP as standard equipment. Rotor Hats Big Brake - Short Offset GT Series Big Brake Short Offset hats are precision machined from premium aluminum alloys for high strength and attention to minimized weight. Hats in this category feature threaded rotor mount holes for use with standard through-hole mount rotors. Threaded hole hats may also be used with T-Nuts or bobbins designed for use with specially machined slotted hole dynamic mount rotors. When used in conjunction with matched Wilwood rotor hardware kits, GT hats provide solid, reliable performance in the most demanding conditions. Short Offset Hats are for narrow space applications with offsets often less than 1.00". They are available for most rotor bolt patterns in a variety of four and five lug wheel patterns. Shallow Offset Hats are for narrow space applications with offsets often less than 1.00". They are available for most rotor bolt patterns in a variety of four and five lug wheel patterns. Check clearance diagram below to ensure proper fitment with your wheel application. -
C5 Wilwood Corvette Rear Big Brake Kit
$2,099.00Superlite 4R Corvette Big Brake Rear Brake Kit For OE Parking Brake Pistons: 4 Rotor Diameter:14 Caliper Mount: Radial Min. Wheel Diameter: 18 Compatible with Chevrolet Corvette 2010-2011 Chevrolet Corvette C-5 1997-2004 All C-5 & ZO6 Rear Disc Chevrolet Corvette C-6 2005-2010 All Rear DiscThe new C5 Corvettes were a departure from the previous models in body design, chassis engineering and engine development. The Corvette horsepower increased greatly from 1997 to 2004 and during this generation, the engineers at Bowling Green developed the special Z06 package that included a 405 horsepower engine. Considering that is net rating instead of gross, that is more power than any of the old 427 engines. Corvettes have always been track cars, but now they had the power to really make a difference. Wilwood Engineering recognized the fun enthusiasts were having with their Corvettes, so they came out with several excellent brake kits. Track enthusiasts could order a W6A Big Brake Kit (Race) for high heat situations. A matching rear race kit is also available. The Corvette can also be equipped with a Superlite 6R Big Brake Front Brake Kit that can be ordered with 13.06 and 14-inch rotors. Matching Superlite 4R Big Brake Rear Brake Kits are also available with 12.88 and 14-inch rotors. Wilwood also offers Pro Matrix front and rear rotor kits and they have a complete listing of high performance brake pads for the original Calipers.Billet Superlite 4R four piston calipers are combined with BP-10 compound pads and 13”-14” rotors in this group of big brake kits for custom high-performance street and show machines. This group of specialized kits for cars, trucks, and SUV’s retain full use of the OE parking brake, master cylinder output, and ABS where used. SL4R rear kits provide complimentary style and performance with 13” and larger front brake upgrades in conjunction with wheel, tire, and suspension upgrades. Optional caliper finishes and rotor designs enable the builder to match style and performance on all applications.Calipers Billet Narrow Superlite 4 The Superlite caliper series has set the standard for many years in short track, late model, modified and open wheel competition. It has also enjoyed prominence in a variety of road-race, off-road, rally and sport driving applications. Starting at 4.40 pounds, the Forged Billet Superlite (FSL) is the newest innovation to this series from Wilwood. New and adaptive technologies have been applied providing substantial improvements in strength, fluid volume displacement, and overall performance. The Superlite caliper series has set the standard for many years in short track, late model, modified and open wheel competition. It has also enjoyed prominence in a variety of road-race, off-road, rally and sport driving applications. Starting at 4.40 pounds, the Forged Billet Superlite (FSL) is the newest innovation to this series from Wilwood. New and adaptive technologies have been applied providing substantial improvements in strength, fluid volume displacement, and overall performance. The FSL body design is a highly efficient product of computer generated solid modeling and stress analysis technology. Each caliper features closed end bridges with a radial transition to the piston body housings. The elimination of machined steps and sharp shoulders in this critical area provides a measurable increase in overall body strength and resistance to deflection under load. Center bridge bolts replace cotter pins to provide additional support and allow quick access with positive brake pad retention. Clamping force, structural deflection, and volume displacement tests have proven the superior strength and efficiency of the FSL. On-track testing has proven driver satisfaction. The bottom line is better stopping power with less pedal travel. The superior strength of this innovative new caliper is combined with proven performance features from other Wilwood designs. Each caliper is equipped with Wilwood's replaceable SRS stainless steel bridge plates. SRS plates eliminate the bridge wear caused by pad gouging and extend the service life of the caliper body. The spring-loading action of the SRS plates also eliminates pad rattle and dampens the vibration harmonics that contribute to squeal under braking. Other standard Wilwood features include high-temperature, square faced o-ring seals for positive sealing, controlled piston retraction, and long service life in high heat conditions. Stainless steel pistons are used to resist corrosion and retard heat transfer from the pads. Fluid tubes are vibration dampened to resist stress fractures and reduce damage caused by track debris. Two-piece bleed screw assemblies provide long, reliable service life and are easily replaced if necessary. Forged Billet Superlite calipers are a direct replacement for all Wilwood Superlite and similar competitive brand calipers with 3.50" centered mounting tabs. Calipers are available in the popular 1.75", 1.62”, 1.38", 1.25” and 1.12” piston sizes for .81", 1.10" and 1.25" rotor widths. FSL calipers use the same 7420 type bridge bolt brake pad used in all Superlite 6 piston calipers. The full range of PolyMatrix pad compounds is available to match brake response and heat range to any application. Rotors GT-72 curved vane rotors are built for the extreme conditions of professional motorsports. The superior heat absorption and dissipation characteristics of these heavy wall directional vane rotors are the keys to preventing heat fade and realizing long service life from the rotors and pads. All rotors are cast from premium grade, long grain carbon iron for long wear, thermal stability, and resistance to distortion. Every GT rotor is fully detail machined to eliminate stress points and unnecessary weight away from the pad sweep face. The faces and O.D. are precision turned to less than .001" for flatness, parallelism, and run-out. An asymmetrical face slot pattern provides smoother engagement through reduced harmonics and improved thermal balance between the I.D. and O.D. of the rotor. Every rotor is then individually dynamic balanced to provide vibration free performance at any speed. These rotors provide the highest cooling capacity and longest service life for extreme braking short tracks and road course competition. Rotor HatsParking Brake Hat - Standard These premium grade cast iron hats are used with Wilwood's internal shoe parking brake kits. Each hat is a precision machined, threaded hole design for use in conjunction with through-hole mount rotors. After machining, the hats are electro-coated for corrosion resistance.Check clearance diagram below to ensure proper fitment with your wheel application. Note(s): 1. 14" Rotor 2. Kit will require aftermarket wheel spacers of 1/8th" (not included in kit) for rear kit installation with OE wheels.Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 Corvette -
2010-2013 Camaro Wilwood Rear Big Brake Kit
Free ShippingCompatible with:2010-2013+ Chevrolet Camaro - All ModelsThe Camaro engineers developed a vehicle, which was released to the public in 2010-2013 with tremendous fanfair and popularity, that is an absolute monster. The Previous generation Camaro hadn't been produced in years, so Chevrolet went back to the drawing board and released a gorgeous and powerful vehicle that has been turning heads since it hit the market. Two models of the Camaro were released. One of them is a tamer, yet still powerful, V6 powered machine, and the other is a 400+HP LS powered monster that performs as well as or better than all of its standard competition. Obviously both of the new Camaros are performers so Wilwood offers several brake improvement kits. These Wilwood Big Brake kits come in various different applications to match the performance style needs of your Camaro, and being that they're Wilwood, you can be absolutely certain that you are getting the very best for your dollar. Wilwood has been tearing up the performance brake scene for some time now, and the reviews for their products are universally outstanding. Billet Superlite 4R four piston calipers are combined with BP-10 compound pads and 13”-14” rotors in this group of big brake kits for custom high performance street and show machines. This group of specialized kits for cars, trucks, and SUV’s retain full use of the OE parking brake, master cylinder output, and ABS where used. SL4R rear kits provide complimentary style and performance with 13” and larger front brake upgrades in conjunction with wheel, tire, and suspension upgrades. Optional caliper finishes and rotor designs enable the builder to match style and performance on all applications. CalipersBillet Narrow Superlite 4The Superlite caliper series has set the standard for many years in short track, late model, modified and open wheel competition. It has also enjoyed prominence in a variety of road-race, off-road, rally and sport driving applications. Starting at 4.40 pounds, the Forged Billet Superlite (FSL) is the newest innovation to this series from Wilwood. New and adaptive technologies have been applied providing substantial improvements in strength, fluid volume displacement, and overall performance. The Superlite caliper series has set the standard for many years in short track, late model, modified and open wheel competition. It has also enjoyed prominence in a variety of road-race, off-road, rally and sport driving applications. Starting at 4.40 pounds, the Forged Billet Superlite (FSL) is the newest innovation to this series from Wilwood. New and adaptive technologies have been applied providing substantial improvements in strength, fluid volume displacement, and overall performance. The FSL body design is a highly efficient product of computer generated solid modeling and stress analysis technology. Each caliper features closed end bridges with a radial transition to the piston body housings. The elimination of machined steps and sharp shoulders in this critical area provides a measurable increase in overall body strength and resistance to deflection under load. Center bridge bolts replace cotter pins to provide additional support and allow quick access with positive brake pad retention. Clamping force, structural deflection, and volume displacement tests have proven the superior strength and efficiency of the FSL. On-track testing has proven driver satisfaction. The bottom line is better stopping power with less pedal travel. The superior strength of this innovative new caliper is combined with proven performance features from other Wilwood designs. Each caliper is equipped with Wilwood's replaceable SRS stainless steel bridge plates. SRS plates eliminate the bridge wear caused by pad gouging and extend the service life of the caliper body. The spring-loading action of the SRS plates also eliminates pad rattle and dampens the vibration harmonics that contribute to squeal under braking. Other standard Wilwood features include high-temperature, square faced o-ring seals for positive sealing, controlled piston retraction, and long service life in high heat conditions. Stainless steel pistons are used to resist corrosion and retard heat transfer from the pads. Fluid tubes are vibration dampened to resist stress fractures and reduce damage caused by track debris. Two-piece bleed screw assemblies provide long, reliable service life and are easily replaced if necessary. Forged Billet Superlite calipers are a direct replacement for all Wilwood Superlite and similar competitive brand calipers with 3.50" centered mounting tabs. Calipers are available in the popular 1.75", 1.62”, 1.38", 1.25” and 1.12” piston sizes for .81", 1.10" and 1.25" rotor widths. FSL calipers use the same 7420 type bridge bolt brake pad used in all Superlite 6 piston calipers. The full range of PolyMatrix pad compounds is available to match brake response and heat range to any application. RotorsGT-72 curved vane rotors are built for the extreme conditions of professional motorsports. The superior heat absorption and dissipation characteristics of these heavy wall directional vane rotors are the keys to preventing heat fade and realizing long service life from the rotors and pads. All rotors are cast from premium grade, long grain carbon iron for long wear, thermal stability, and resistance to distortion. Every GT rotor is fully detail machined to eliminate stress points and unnecessary weight away from the pad sweep face. The faces and O.D. are precision turned to less than .001" for flatness, parallelism, and run-out. An asymmetrical face slot pattern provides smoother engagement through reduced harmonics and improved thermal balance between the I.D. and O.D. of the rotor. Every rotor is then individually dynamic balanced to provide vibration free performance at any speed. These rotors provide the highest cooling capacity and longest service life for extreme braking short tracks and road course competition. Rotor Hats Parking Brake Hat - Standard These premium grade cast iron hats are used with Wilwood's internal shoe parking brake kits. Each hat is a precision machined, threaded hole design for use in conjunction with through-hole mount rotors. After machining, the hats are electro-coated for corrosion resistance. Check clearance diagram below to ensure proper fitment with your wheel application.Note(s):1. 14" Rotor2. Kit will require aftermarket wheel spacers of 1/8th" (not included in kit) for rear kit installation with OE wheels. -
C5 Wilwood Corvette Front Big Brake Kit
$2,399.00W6A Wilwood Big Brake Front Brake Kit Pistons: 6 Rotor Diameter:14.25 Caliper Mount: Radial Min. Wheel Diameter: 18Compatible with the Chevrolet Chevrolet Corvette 2010-2011 Cadilac XLR 2005-2009 All Chevrolet Chevrolet Corvette C-5 1997-2004 All C-5 & ZO6 Chevrolet Chevrolet Corvette C-6 2005-2009 All C-6 & ZO6The new C5 Corvettes were a departure from the previous models in body design, chassis engineering and engine development. The Corvette horsepower increased greatly from 1997 to 2004 and during this generation, the engineers at Bowling Green developed the special Z06 package that included a 405 horsepower engine. Considering that is net rating instead of gross, that is more power than any of the old 427 engines. Corvettes have always been track cars, but now they had the power to really make a difference. Wilwood Engineering recognized the fun enthusiasts were having with their Corvettes, so they came out with several excellent brake kits. Track enthusiasts could order a W6A Big Brake Kit (Race) for high heat situations. A matching rear race kit is also available. The Corvette can also be equipped with a Superlite 6R Big Brake Front Brake Kit that can be ordered with 13.06 and 14-inch rotors. Matching Superlite 4R Big Brake Rear Brake Kits are also available with 12.88 and 14-inch rotors. Wilwood also offers Pro Matrix front and rear rotor kits and they have a complete listing of high performance brake pads for the original Calipers.Wilwood W6AR calipers were designed for the specific purpose of providing big capacity braking with large diameter rotors for heavy weight and extreme duty vehicles. For cars, it’s the biggest of the big providing big brake performance for show and dual purpose street and track vehicles. For trucks and SUV’s, it provides big stopping power for towing, off-road, and enhanced braking with wheel and tire upgrades. Kits listed for specific vehicles are fully compatible with OE master cylinder output and ABS function. Directional staggered vane 14.25” rotors provide maximum cooling for sustained high heat durability. Calipers W6A Radial Mount The W6A forged six-piston caliper delivers heavy duty stopping power for the road or track. The caliper incorporates race technology into a body design with widespread adaptability. Radial mounting, two options for piston volume, and a rotor diameter ranging from 12.19" to 14.25" give this caliper the versatility necessary to suit all types of heavyweight braking requirements. The W6A body is the product of FEA computer design and stress flow forging technology. FEA technology allows the designer to test the prototype in a computer environment to determine the optimal structural design within the dimensional parameters of the component. Stress flow forging produces a part with the internal grain structure of the metal aligned in the direction of the flow of the body contour. The results are a caliper with superior clamping efficiency and ultimate strength against fatigue, stresses, and distortion under load. This caliper generates big brake clamping force with six differential bore stainless steel pistons. Stainless steel is used for its high resistance to corrosion and low thermal conductivity that reduces the heat transfer from the pads. The differential bore pattern balances pad loading to help maintain even pad wear. High-temperature bore seals provide long service life and maintain their resilience to provide positive piston retraction on release. Two options for overall piston volume make it simple to match the calipers with master cylinder output and rear caliper size for correct bias proportioning. The performance of the W6A is enhanced with SRS bridge plates, snap-ring locked pad retainer pins, recessed two-piece bleed screw assemblies and dampen mounted fluid transfer tubes. SRS bridge plates eliminate all bridge wear caused by pad gouging. The spring-loaded action of the plates also eliminates pad rattle. Snap ring clips lock the pad pins in place to provide positive retention and allow easy service without caliper removal. The bleed screws are recess mounted for protection against impact and debris. The fluid tubes are dampen mounted to protect them from fatigue or damage from vibration or debris. Calipers are anodized in high luster black to protect from corrosion and maintain their high-tech appearance. The W6A is also available with a gloss red finish or other custom Wilwood color by order. Radial-mount adapter brackets are used in Wilwood brake kits to provide a secure and precise method of attaching the W6A caliper to the factory mount bosses on the original spindle. Rotors SRP Drilled Performance Rotor SRP Drilled Performance Rotors feature a specially engineered directional cross drill and face slot pattern that improve brake response and pad performance throughout the entire range of light to heavy braking. The venting and cleaning action of the holes and slots will reduce pad glaze and disperse gasses and heat generated during the pad to rotor interface. The holes and slots also inhibit irregular pad compound build-up on the rotor faces resulting in smoother engagement and improved pedal response in all conditions. The material removed also contributes to lower rotating and unsprung suspension weight. Along with the excellent performance characteristics of this rotor design, each rotor is treated with a black electro coat to inhibit corrosion on all areas of the rotor. The high tech design, classic style, and aesthetic appeal of the SRP series are the perfect finishing touches to any wheel and tire detail. SRP rotors are available in all popular sizes used in Wilwood's Pro Series and Big Brake conversion kits. Kits in these categories designated with the drilled rotor option get the SRP as standard equipment. Rotor Hats Big Brake - Short Offset GT Series Big Brake Short Offset hats are precision machined from premium aluminum alloys for high strength and attention to minimized weight. Hats in this category feature threaded rotor mount holes for use with standard through-hole mount rotors. Threaded hole hats may also be used with T-Nuts or bobbins designed for use with specially machined slotted hole dynamic mount rotors. When used in conjunction with matched Wilwood rotor hardware kits, GT hats provide solid, reliable performance in the most demanding conditions. Short Offset Hats are for narrow space applications with offsets often less than 1.00". They are available for most rotor bolt patterns in a variety of four and five lug wheel patterns. Shallow Offset Hats are for narrow space applications with offsets often less than 1.00". They are available for most rotor bolt patterns in a variety of four and five lug wheel patterns. Check clearance diagram below to ensure proper fitment with your wheel application.Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 Corvette -
2010-2013 Camaro Wilwood Front Big Brake Kit
Free ShippingPistons: 6 Rotor | Diameter:14.25 | Caliper Mount:Radial | Min. Wheel Diameter: 18 Compatible with the: 2010-2013+ Chevrolet Camaro - All Models The Camaro engineers developed a vehicle, which was released to the public in 2010-2013 with tremendous fanfair and popularity, that is an absolute monster. The Previous generation Camaro hadn't been produced in years, so Chevrolet went back to the drawing board and released a gorgeous and powerful vehicle that has been turning heads since it hit the market. Two models of the Camaro were released. One of them is a tamer, yet still powerful, V6 powered machine, and the other is a 400+HP LS powered monster that performs as well as or better than all of its standard competition. Obviously both of the new Camaros are performers so Wilwood offers several brake improvement kits. These Wilwood Big Brake kits come in various different applications to match the performance style needs of your Camaro, and being that they're Wilwood, you can be absolutely certain that you are getting the very best for your dollar. Wilwood has been tearing up the performance brake scene for some time now, and the reviews for their products are universally outstanding.Wilwood W6AR calipers were designed for the specific purpose of providing big capacity braking with large diameter rotors for heavy weight and extreme duty vehicles. For cars, it’s the biggest of the big providing big brake performance for show and dual purpose street and track vehicles. For trucks and SUV’s, it provides big stopping power for towing, off-road, and enhanced braking with wheel and tire upgrades. Kits listed for specific vehicles are fully compatible with OE master cylinder output and ABS function. Directional staggered vane 14.25” rotors provide maximum cooling for sustained high heat durability. CalipersW6A Radial MountThe W6A forged six piston caliper delivers heavy duty stopping power for the road or track. The caliper incorporates race technology into a body design with widespread adaptability. Radial mounting, two options for piston volume, and a rotor diameter ranging from 12.19" to 14.25" give this caliper the versatility necessary to suit all types of heavy weight braking requirements. The W6A body is the product of FEA computer design and stress flow forging technology. FEA technology allows the designer to test the prototype in a computer environment to determine the optimal structural design within the dimensional parameters of the component. Stress flow forging produces a part with the internal grain structure of the metal aligned in the direction of the flow of the body contour. The results are a caliper with superior clamping efficiency and ultimate strength against fatigue, stresses, and distortion under load. This caliper generates big brake clamping force with six differential bore stainless steel pistons. Stainless steel is used for its high resistance to corrosion and low thermal conductivity that reduces the heat transfer from the pads. The differential bore pattern balances pad loading to help maintain even pad wear. High temperature bore seals provide long service life and maintain their resilience to provide positive piston retraction on release. Two options for overall piston volume make it simple to match the calipers with master cylinder output and rear caliper size for correct bias proportioning. The performance of the W6A is enhanced with SRS bridge plates, snap-ring locked pad retainer pins, recessed two-piece bleed screw assemblies and dampen mounted fluid transfer tubes. SRS bridge plates eliminate all bridge wear caused by pad gouging. The spring-loaded action of the plates also eliminates pad rattle. Snap ring clips lock the pad pins in place to provide positive retention and allow easy service without caliper removal. The bleed screws are recess mounted for protection against impact and debris. The fluid tubes are dampen mounted to protect them from fatigue or damage from vibration or debris. Calipers are anodized in high luster black to protect from corrosion and maintain their high-tech appearance. The W6A is also available with a gloss red finish or other custom Wilwood color by order. Radial mount adapter brackets are used in Wilwood brake kits to provide a secure and precise method of attaching the W6A caliper to the factory mount bosses on the original spindle. RotorsSRP Drilled Performance RotorSRP Drilled Performance Rotors feature a specially engineered directional cross drill and face slot pattern that improve brake response and pad performance throughout the entire range of light to heavy braking. The venting and cleaning action of the holes and slots will reduce pad glaze and disperse gasses and heat generated during the pad to rotor interface. The holes and slots also inhibit irregular pad compound build-up on the rotor faces resulting in smoother engagement and improved pedal response in all conditions. The material removed also contributes to lower rotating and unsprung suspension weight. Along with the excellent performance characteristics of this rotor design, each rotor is treated with a black electro coat to inhibit corrosion on all areas of the rotor. The high tech design, classic style, and aesthetic appeal of the SRP series are the perfect finishing touches to any wheel and tire detail. SRP rotors are available in all popular sizes used in Wilwood's Pro Series and Big Brake conversion kits. Kits in these categories designated with the drilled rotor option get the SRP as standard equipment. Rotor HatsBig Brake - Short OffsetGT Series Big Brake Short Offset hats are precision machined from premium aluminum alloys for high strength and attention to minimized weight. Hats in this category feature threaded rotor mount holes for use with standard through-hole mount rotors. Threaded hole hats may also be used with T-Nuts or bobbins designed for use with specially machined slotted hole dynamic mount rotors. When used in conjunction with matched Wilwood rotor hardware kits, GT hats provide solid, reliable performance in the most demanding conditions. Short Offset Hats are for narrow space applications with offsets often less than 1.00". They are available for most rotor bolt patterns in a variety of four and five lug wheel patterns. Shallow Offset Hats are for narrow space applications with offsets often less than 1.00". They are available for most rotor bolt patterns in a variety of four and five lug wheel patterns. Check clearance diagram below to ensure proper fitment with your wheel application.
8 Item(s)
Wilwood Brakes
Minimal Price: $ 1,999.00 1999
Brand Search
All Categories
-
Corvette C8 Parts
- Corvette C8 Accessories
- Corvette C8 Apparel
- Corvette C8 Brakes
- Corvette C8 Car Care Products
- Corvette C8 Car Covers
- Corvette C8 Carbon Fiber
- Corvette C8 Exhaust
- Corvette C8 Lloyd Floor Mats
- Corvette C8 Home & Garage Gear
- Corvette C8 Interior Parts
- Corvette C8 Maintenance
- Corvette C8 Performance Parts
- Corvette C8 Wheels
- Corvette C8 Engine Dress Up
- Corvette C8 Exterior Parts
- Corvette C8 Stingray Custom Painted Parts
-
Corvette C7 Parts
- Corvette C7 Accessories
- Corvette C7 Apparel
- Corvette C7 Brakes
- Corvette C7 Car Care Products
- Corvette C7 Car Covers
- Corvette C7 Carbon Fiber
- Corvette C7 Exhaust
- Corvette C7 Exterior Parts
- Corvette C7 Lloyd Floor Mats
- Corvette C7 Home & Garage Gear
- Corvette C7 Interior Parts
- Corvette C7 Maintenance
- Corvette C7 Performance Parts
- Corvette C7 Under Hood Dress Up
- Corvette C7 Wheels
- Corvette C7 Hot New Products
-
Corvette C6 Parts
- Corvette C6 Wheels
- Corvette C6 Accessories
- Corvette C6 Apparel
- Corvette C6 Brakes
- Corvette C6 Car Care Products
- Corvette C6 Car Covers
- Corvette C6 Engine Dress Up
- Corvette C6 Engine Parts
- Corvette C6 Exhaust
- Corvette C6 Exterior
- Corvette C6 Floor Mats
- Corvette C6 Intake
- Corvette C6 Interior
- Corvette C6 Shift Knobs
- Corvette C6 Suspension Parts
- Corvette C6 Transmission Parts
- Corvette C6 Tuners-Miscellaneous
- Corvette C6 LED And Lighting
- 1953-1996 Corvette Restoration Parts
-
2016-2023 Camaro Parts and Accessories
- 2016-2023 Camaro Air Intake Systems
- 2016-2023 Camaro Apparel
- 2016-2023 Camaro Brakes
- 2016-2023 Camaro Car Care Products
- 2016-2023 Camaro Car Covers
- 2016-2023 Camaro Engine Bay Dress-Up
- 2016-2023 Camaro Exhaust Systems
- 2016-2023 Camaro Exterior Parts
- 2016-2023 Camaro Floor Mats
- 2016-2023 Camaro Interior Parts
- 2016-2023 Camaro Misc. Accessories
- 2016-2023 Camaro Performance Parts
- 2016-2023 Camaro Suspension
- 2016-2023 Camaro Wheels and Accessories
-
2010-2015 Camaro Parts & Accessories
- 2010-2015 Camaro Air Intake Systems
- 2010-2015 Camaro Apparel
- 2010-2015 Camaro Brakes
- 2010-2015 Camaro Car Care Products
- 2010-2015 Camaro Car Covers
- 2010-2015 Camaro Engine Bay Dress-Up
- 2010-2015 Camaro Exhaust
- 2010-2015 Camaro Exterior Parts
- 2010-2015 Camaro Floor Mats
- 2010-2015 Camaro Headers
- 2010-2015 Camaro Interior Parts
- 2010-2015 Camaro Misc. Accessories
- 2010-2015 Camaro Performance Products
- 2010-2015 Camaro Suspension
- 2010-2015 Camaro Wheels
- 2010-2015 Seibon Camaro Carbon Fiber
-
Corvette C5 Parts
- Corvette C5 Accessories
- Corvette C5 Body Parts
- Corvette C5 Brakes
- Corvette C5 Car Care Products
- Corvette C5 Car Covers
- Corvette C5 Engine Dress Up
- Corvette C5 Engine
- Corvette C5 Exhaust
- Corvette C5 Exterior
- Corvette C5 Floor Mats
- Corvette C5 Exhaust Header Systems
- Corvette C5 Intake
- Corvette C5 Interior
- Corvette C5 Miscellaneous Parts
- Corvette C5 Nitrous Kits
- Corvette C5 Shift Knobs
- Corvette C5 Suspension and Steering
- Corvette C5 Wheels
- Corvette C5 Replacement Carpet Packages
-
2015-2019 6th Generation Ford Mustang
- 2015-2019 Ford Mustang Car Covers
- 2015-2019 Ford Mustang Custom Painted
- 2015-2019 Ford Mustang Emblems, Decal
- 2015-2019 Ford Mustang Engine Dress Up
- 2015-2019 Ford Mustang Exhaust System
-
2015-2019 Ford Mustang Exterior Parts
- 2015-2019 Ford Mustang Grilles
- 2015-2019 Ford Mustang License Plate Frames
- 2015-2019 Ford Mustang Lighting & Blackouts
- 2015-2019 Ford Mustang Misc Exterior Accessories
- 2015-2019 Ford Mustang Spoilers and Splitters
- 2015-2019 Ford Mustang Stripes and Decals
- 2015-2019 Ford Mustang Carbon Fiber Body Parts
- 2015-2019 Ford Mustang Interior Parts
- 2015-2019 Ford Mustang License Plate
- 2015-2019 Ford Mustang Light Blackout
- 2015-2019 Ford Mustang Lloyd Floor Mats
- 2015-2019 Ford Mustang Performance
- 2015-2019 Ford Mustang Wheels
- 2015-2019 Ford Racing Parts
- 2015-2019 Ford Mustang Brakes
-
2009-2023 Dodge Challenger Parts
- 2009-2023 Challenger Car Covers
- 2009-2023 Challenger Cold Air Intake
- 2009-2023 Challenger Engine Dress-Up
- 2009-2023 Challenger Interior Parts
- 2009-2023 Challenger Suspension Parts
- 2009-2023 Challenger Wheels
- 2009-2023 Dodge Challenger Brakes
- 2009-2023 Dodge Challenger Exhaust Systems
- 2009-2023 Dodge Challenger Exterior Parts
- 2009-2023 Dodge Challenger Floor Mats
- 2009-2023 Dodge Challenger Headers
- 2009-2023 Dodge Challenger Tuners
- 2009-2023 Challenger Carbon Fiber
- 2010-2014 Ford Raptor Parts
- 2017-Current Ford Raptor
- Beltronics Radar Detectors
- Cadillac ATS
- Corvette America
- 2015-2023 Hellcat Challenger Parts
- MBRP Exhaust
- S&B Filters
- SPAL Fans
- Teraflex
- Allstar Performance
- Baja Designs
- 3D MAXpider
- Fab Fours
- XDP
- Volunteer Vettes
- Diode Dynamics
- Oracle
- Du Ha
- aFe Power
- Diamond Eye
- APR Performance
- Rigid Industries
All Manufacturers
- ACI
- Adjure
- Advanced Composite Specialties
- aFe Power/Pfadt
- Akrapovic Exhaust
- Altec
- American Brothers Design
- American Car Craft
- American Racing Headers
- Anderson Composites
- AP Racing
- APR Performance
- Arkon
- Auto Care Products
- Auto Custom Carpets
- Auto Etc Neon
- Baer
- Bassani
- BB Exhaust
- BBK
- Beltronics
- Blendmount
- BM
- BMR
- Borla
- Brembo
- California Car Cover
- Callaway Cars Inc
- Caspers Electronics
- CBD
- CEI
- ChargerConnection
- Cobb Tuning
- Cold Air Inductions Inc
- Corsa
- Corvette America
- Corvette Eyewear
- Covercraft
- CoverKing
- CPX Foilers
- CS Vettes
- CTEK
- Custom LED Service
- Dashtronix
- DBA Disc Brakes
- DefenderWorx
- Diablo Sport
- Diode Dynamics
- DSVette
- Dynamat
- East Coast Supercharging
- Edelbrock
- EED
- Eibach
- Elite
- Elite Engineering
- Empire Vehicle Accessories
- Escort Radar Detectors
- Extreme Dimensions
- Factory Reproductions
- FAST Peformance
- Fidanza
- Flowmaster
- Forgeline Wheels
- GHL Motorsports
- GM
- Green Air Filters
- Green Light
- Halltech
- Hawk Performance
- Heat Metal Corp.
- HiTech
- Hotchkis
- Hurst
- Husky Liners
- Hyperco
- IForged Performance Alloys
- Innovative Vehicle Solutions
- JLT
- Kirban Performance
- KN Filters
- Kooks Custom Headers
- Koolmat
- Lewis Five Motorsports
- LG Motorsports
- Lingenfelter
- Lloyd Mats
- LSD
- MagnaFlow
- Magnuson
- Melrose Tops
- Metro Vacuum
- MGP
- Mine's
- Momo Italy
- MRT
- MSD
- MTI
- NOCO Genius Battery Chargers
- Norscot
- NOS
- OER
- Password JDM
- Performance Choice
- PFADT Race Engineering
- Pioneer
- Power Slot
- R2C Performance Products
- Race Ramps
- RaceMesh
- Ralph White Merchandising
- RAM Clutches
- Retro USA
- Roto-Fab
- Roush Performance
- RPI Designs
- Russell
- SB Filters
- SCX
- Seibon Carbon
- SLP
- Southern Car Parts
- Southern Car Parts
- Spal
- SpeedLingerie
- Stainless Works
- Starcraft
- StarCraft
- Stillen
- Superior Dash
- Taylor
- TeraFlex
- TiTek
- TopDown
- Trufiber
- TSW Wheels
- UltraRacing
- Vararam
- Vertical Doors Inc.
- Vette Net
- VIS Racing Sports
- Volunteer Vettes
- WCC Forged
- Webelectric
- West Coast Corvette
- Wilwood Brakes
- Wow Thats It's
- Xtreme Diesel Performance
- Zippo
- Zoom Performance
Corvette Information
- Brembo GT Brake Upgrade Questions
- Camaro Havoc Body Kit Installation Instructions
- Choosing a Limited Slip Differential
- Corvette C5 and C6 Brake Pad Replacement
- Corvette C5 Common Problems
- Corvette C5 DIC Codes
- Corvette C5 Facts 00-04
- Corvette C5 Facts 97-99
- Corvette C5 Intake Installation
- Corvette C6 DIY, Differential Oil Change
- Corvette C6 F55 Console Installation
- Corvette C6 Facts 05-07
- Corvette C6 Full Length Spoiler Install
- Corvette C6 HID Foglights Mod/DIY
- Corvette C6 Model Year Changes
- Corvette C6 Nav System Mod
- Corvette C6 RPO Codes
- Corvette C6 VIN Decoder
- Corvette C6 Z06 Battery Charger Installation
- Corvette C6 Z06 Brembo Brake Installation
- Corvette C6 Z06 Exhaust Sound Comparison
- Corvette C6 ZR1 Blue Devil Information
- Corvette C7 Information
- Corvette Clubs
- Corvette Information for the C6
- Corvette Paint Codes
- Corvettes For Sale
- Coupon Codes
- How to Change your Oil-2010 Camaro
- Index
- Southern Car Parts Banners
- Shipping & Returns
- Privacy Notice
- Conditions of Use
- 2008 Corvette C6 Pricing
- 2009 Corvette C6 Information
- 2009 Corvette C6 Pricing
- 2014 Corvette C7 Stingray
- Akrapovic Exhaust Pictures
- Aluminum Race Pedals Installation Instructions
- Gift Voucher FAQ
- Contact Us
- Site Map
- Package Tracking
- Corvette Resources
- Corvette Floor Mat Pictures
Hot New Products
There are no feature products.
Top Selling Products
About company
Chevrolet,Camaro and Corvette are registered trademarks of General Motors Corporation.
Southern Car Parts has no affiliation with General Motors Corporation.
Contact Information
Phone: 1-888-631-1433 Email UsWhy buy from us
X