Corvette C6 Tuners-Miscellaneous


Corvette C6 Tuners-Miscellaneous

2005-2013 Corvette C6 Tuners and Miscellaneous Parts

Corvette C6 Electronic Engine Tuners and Miscellaneous Component Products

We sell over a thousand unique parts for the Corvette vehicles here at Southern Car Parts, and sometimes it's difficult to classify where one part or another belongs. These parts--the seeming miscellany--these are the parts that can really complete a Corvette, so we want to be sure to list them. Items like Corvette Tuners, Corvette Electronic Wiring Harnesses, Corvette Exhaust Command Switches, and other such products are incredibly important and can really come together to complete a show or track quality C6 Corvette.

25 Item(s)

Grid List

Set Descending Direction
  • 2005-2013 C6 Corvette LG Motorsports Super Cool Radiator

    2005-2013 C6 Corvette LG Motorsports Super Cool Radiator

    $953.33
    Free Shipping
    With a larger cooling capacity the Super Cool Radiator from LG Motorsports can reduce your C6 engine teperature by up to 30 degrees! LG's newest design for the C6 Corvette offers a much larger cooling capacity and is a plug and play installation. Our radiator will show water temperature drops of up to 30 degrees to keep your cool in the summer heat. This radiator also offers GM style hook ups for the factory automatic or Z51 manual transmission cooler and features an optional built in oil cooler. All aluminum contruction thick 2" core increased water capacity drop in replacement uses OEM style fittings on engine oil and transmission coolers reduction of up to 30 degree water temps reduction of up to 20 degree engine oil temps reduction of up to 20 degree transmission temps Application 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • C5-C6 Intake Air Temperature Harness Extension 36"

    C5-C6 Intake Air Temperature Harness Extension 36"

    $25.95
    If you have ever installed an aftermarket cold air intake into your Corvette only to discover that the IAT sensor was moved and now your harness cannot be plugged back in. You cannot cut and splice oxygen sensor wiring since this can permanently damage the sensor and considerably reduce accuracy of the signal. This extension is "Plug-And-Play" and utilizes OEM connectors, terminals and seals with OEM wiring to maintain precisely accurate signals and safely extend the wiring connections.  Note: Please check your connector shape and color to see if it matches your application. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 Corvette
  • C6 Corvette Pedal Commander Throttle Response Controller

    2006-2013 C6 Corvette Pedal Commander Throttle Response Controller

    Regular Price: $349.99

    Special Price $299.99

    Free Shipping
    Are you looking for instant throttle response while smashing the throttle on your C6 Corvette? If so, then you want to pick up a Pedal Commander and enjoy all the benefits! Eliminates Delay. Nowadays, vehicles are notorious for their delayed throttle response. That's where the Pedal Commander comes in. These days, vehicles use a drive-by-wire system that monitors the position of the gas pedal to control the throttle electronically, similar to a dimmer switch. The problem with this setup is that the signal from the pedal has to first be sent the ECU, which in turn then sends the signal to the actuator motor that controls the throttle body itself. This delay is most noticeable when trying to speed up to merge with fast moving traffic or pass a slower moving car. However, the Pedal Commander Bluetooth Throttle Response Controller will eliminate that delayed throttled response, giving your vehicle a drastic night and day difference in performance. Four Adjustable Control Modes. Unlike other throttle control devices that are either on or off, the Pedal Commander comes with 4 control modes: Eco, City, Sport and Sport +. Best of all, each mode has an additional 8 different levels of sensitivity which allows you to personally adjust each mode to your own personal driving style and needs. Switching between modes can be done manually on the Commander or can also be done using your smartphone (Pedal Commander App), without having to bend over and physically touch the Pedal Commander. Compatible with Aftermarket Programmers. The Pedal Commander can be used in conjunction with common aftermarket OBD-II programmers and/or monitors such as: SCT, Diablosport, Hypertech, Superchips, Bully Dog, and Edge. 2-Year Product Warranty. Pedal Commander manufactures their Bluetooth Throttle Response Controller to the highest quality and standards with CE and TUV Certification. However in the event you do receive a defective or malfunctioning device, Pedal Commander will replace it free of charge within 2 years of the original purchase date. Easy Plug & Play Installation. The Pedal Commander Throttle Response Controller connects directly into the stock throttle position sensor found on the drive-by-wire gas pedal using an OEM style plug and play connector with no permanent modifications required. The Pedal Commander is 100% reversible making it warranty friendly. (Does not fit 2005) Application: 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • C6 Corvette Big Brake Front Kit AP Racing

    C6 Corvette Big Brake Front Kit AP Racing

    $3,739.00
    Free Shipping
    For all C6 Corvette 's, including the Z06 and Z51 Packages. For the biggest brake system upgrade, Brake Pros offers world renown AP Racing 6-piston calipers running on 2-piece 14.25" rotors. Each kit is designed to work with the original equipment master cylinder, ABS and traction control systems. Specially-designed 2-piece rotors are cross-drilled and slotted, the optimum for high-performance street, autocross and occasional track day use. Slotted-only versions are available for the serious track enthusiast. The curved vane construction provides maximum cooling, while significantly reducing unsprung weight. DOT-compliant and TÜV-approved stainless steel lines are included to top off the upgrade and provide a huge improvement in pedal feel and stiffness. Brackets and hardware are made from aerospace-grade materials and high-strength fasteners. All AP Racing kits are complete with no other parts required. Install, bleed and go! Many kits require 17" wheels or larger with sufficient spoke clearance. Download a brake profile template to check your wheels before ordering. Put decades of championship-winning experience on your car. It's not just for Formula One and NASCAR winners anymore. Or LeMans, or British Touring Cars, or WRC, or Grand Am, or Super GT, or DTM... Installation Instructions Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • 2005-2013 C6 ZR1 Corvette LG Motorsports Radiator

    2005-2013 C6 ZR1 Corvette LG Motorsports Radiator

    $1,154.70
    Free Shipping
    With a larger cooling capacity this Radiator from LG Motorsports reduces the temperature of your C6 ZR1 by up to 40 degrees! Easy to install! In extensive testing with our in house ZR1 we found early on that the stock radiator was barely able to hold up to the stock car, much less a ZR1 making 200-300 more HP than stock. Our radiator is a plug and play upgrade for the stock unit and can see water temp reductions of up to 40 degree's F, Oil temp reduction of almost 30 degree's, and trans temp reductions of 30 degree's as well. Highly suggested to use with a 160 thermostat. C6Z06 with the Z07 package can use this radiator as well when combined with the ZR1 upper radiator hose and trans cooler fittings. Application 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 ZR1 Corvette
  • C5-C6 Corvette Air Fuel Gauge Wiring Pigtail

    C5-C6 Corvette Air Fuel Gauge Wiring Pigtail

    $17.95
    Used on OBD I and II applications using the four-wire sensors. This harness allows an aftermarket air-fuel gage to be added to your current front oxygen sensor signal, with complete plug-in capability. Signal wire exits the plug-in assembly and allows the addition of wire for your gage without cutting up your factory harness. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 Corvette
  • 2006-2013 C6/Z06 Corvette LG Motorsports Super Cool Radiator

    2006-2013 C6/Z06 Corvette LG Motorsports Super Cool Radiator

    $729.95
    Free Shipping
    The Super Cool Radiator from LG Motorsports has a large cooling capacity and is easy to install! Cool off your C6 Corvette! LG's newest design for the C6 Corvette offers a much larger cooling capacity and is a plug and play installation. Our radiator will show water temperature drops of up to 30 degrees to keep your cool in the summer heat. This radiator also offers GM style hook ups for the factory automatic or Z51 manual transmission cooler and features an optional built in oil cooler. *Base C6 cars without the Z51 option wanting to use the oil cooler must purchase oil line kit All aluminum contruction thick 2" core increased water capacity drop in replacement uses OEM style fittings on engine oil and transmission coolers reduction of up to 30 degree water temps reduction of up to 20 degree engine oil temps reduction of up to 20 degree transmission temps Application 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette Z06
  • C6 C5 Corvette Knock/Cam Harness LS1 to LS2/LS7

    C6 C5 Corvette Knock/Cam Harness LS1 to LS2/LS7

    $53.25
    Cam Harness This harness allows the cam sensor used on the front of a LS2 motor to be plugged into the LS1 cam sensor connector located at the back of the intake manifold. This harness is perfect for LS2 motor conversions. Compatible with the PCM harness in LS1 Corvette and F-Body cars.    Knock Harness This harness allows the single-wire LS1 knock sensors located on top of the LS1 manifold to be relocated on both sides of the LS2 block and plugged into the factory LS1 PCM harness. It has the perfect added length and thermal protection required to be routed near hot exhaust manifolds. Compatible with the PCM harness in LS1 Corvette and F-Body cars.
  • C6 Corvette RAM Powergrip Clutch

    C6 Corvette RAM Powergrip Clutch

    $409.99
    Powergrip RAM Clutch for C5, C5 Z06, C6, C6 Grand Sport, and C6 Z06 Model C6 Corvettes This RAM Powergrip clutch is designed to provide the best blend of benefits for Street, Track, and Drag Strip uses! Built to provide the strength and holding power necessary for the Drag Strip, yet still be soft and easy enough for regular street driving. That happy medium is not often met by aftermarket clutches, but this RAM Powergrip does that and much more! With its superior design and manufacturing, this clutch is a fantastic choice for any C6 Corvette putting out 550HP or less. This clutch uses RAM Powergrip Performance 900 and 300 series organic friction materials. These materials provide excellent controlling power that's coupled with smooth drivability and minimal chatter (although, some may still be noticeable upon take-off). High-performance street/strip Organic material SFI approved Rated to 550 HP Fits 97-13 C5, C5 Z06, C6, Grand Sport, or C6 Z06 Specs: Fits: all C5, all C5 Z06, and 05-13 C6, C6 Grand Sport, C6 Z06 Disc diameter: 11" Spline: 26 Horsepower rating: 550 HP Includes alignment tool. *Notes: *05+ C6 Corvettes must combine this clutch with a Ram Billet Flywheel (sold separately). RAM strongly recommends using a billet steel flywheel or factory nodular iron (explosion-resistant) flywheel with this clutch. Works with factory hydraulics (01+). Extreme flywheel wear/resurfacing may require a RAM adjustable master cylinder. Clutch is not compatible with Tremec transmissions. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette Z06, ZR1, Grand Sport Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 CORVETTE, Z06
  • C6 Corvette Mild to Wild Exhaust On Demand Switch

    C6 Corvette Mild to Wild Exhaust On Demand Switch Mild2Wild

    Regular Price: $69.95

    Special Price $68.40

    Free Shipping
    Imagine having the ability to turn your C6 Corvette Z06, Grand Sport, ZR1, and NPP exhaust from MILD (exhaust ports closed) to WILD (exhaust ports open) using your OEM Homelink (found on your visor) or via the supplied remote. This revolutionary product lets you control your, 2006-Present Corvette Z06, ZR1, Grand Sport or NPP exhaust system on demand via a tiny wireless remote or the Homelink feature in your car. One of the coolest technologies on the new C6 Z06, ZR1, Grand Sport, and 2007+ NPP equipped Corvette is the “bi-mode” exhaust. Whisper quite up until 3500 RPM and then a wide-open race car sounds as the flaps located in the tips open. The problem is the inability to control this feature. Up until now, the owner’s only choice was to pull the fuse or to install wiring, drill a hole for a switch to turn the quiet mode off (and these sell for $85). After spending $75,000, the last thing I would want to do is start running wires and drilling holes. This patent-pending product requires no drilling or running wires through your car. It’s a simple 5 min simple plug and play installation that anyone can do. Once installed, you will have full control over the exhaust mode, via a simple ON/OFF remote wireless controller or your Homelink transmitter (simple programming required, instructions provided. Please be aware that not all Corvettes use Homelink, some use Car2U. You will need to use the remotes if your car is equipped with Car2U). Once the Homelink is programmed, you can just use that to work your exhaust. You also will get two sleek ON/OFF wireless controls that can be mounted anywhere and will control the exhaust up to 50’ away. The “OFF” mode gives you that race car sound 100% of the time. The “ON” mode works as the stock setting and is quiet to preset OEM 3,500 RPM so the system will work just like the stock system. The switch can be used anytime the car is running, allowing you to show your friends what a cool exhaust you have as you can use the remote and open and close the flaps on demand. Baffles Open, Wild..... Baffles closed, Mild..... You will receive the professionally engineered plug and play wireless receiver, two miniature remotes (batteries included) and the necessary Homelink programming instructions. Believe me, you will be happy with the quality and fit of this Corvette exhaust controller. NOTE: this unit will work with either of the supplied remotes or the OEM visor mounted Homelink system. It will not work with other visor-mounted units. GM has been testing other visor units, so you may not have a Homelink system. If you have a visor unit with a single LED with the home symbol around it you have Homelink and this will work with the visor controls. If not, you will need to use the included remotes. Installation Instructions are Located Here Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • Lock In C6 Corvette C5 Jacking Pucks

    C6-C5 Corvette Lock In Jacking Pucks

    $42.99
    Free Shipping
    1997-2013 Corvette Leave In Jacking Pucks Corvette Jacking Pucks for all C5 and C6 Corvettes  The ultimate jacking solution for your C5 or C6 Corvette (will not lock in place on the C6 Z06 and C6 ZR1). Brand new, leave in place jacking pucks. Our Corvette jacking pucks are low profile and will last as long as you own your car. They "pop" right into your jack hole and you can then leave them in place without ever needing to remove them. The easily snap into place and will be there if you ever need to jack up your car. They are not noticeable under the car and look like a factory OEM piece (not sure why GM did not include them in the first place). They can also be popped right back out if you ever need to remove them. Made from durable plastic, they will last the life of your car and you can rest assured you will never be stuck in a situation where you need to jack up the car and do not have jacking pucks. Will not fit C6 Z06, ZR1 Will not fit C6 Z06, ZR1 Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette  Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 Corvette  
  • 1997-2013 C5 C6 Corvette Seat Rebuild Kit

    1997-2013 C5 C6 Corvette Seat Rebuild Kit

    $39.95
    Seat Foam and Padding Rebuild Kit for the C5 and C6 Corvette Nothing feels better than a rebuilt seat driving down the road in your C5 or C6 Corvette. But if your vehicle is 8, 9 or even 10 years old, or more there's a pretty good chance your seats, especially your driver seat is starting to show its age. The ride is probably not as comfortable as it once was and has probably been declining over time until you know this to this all at once. So if you are on this page looking for a rebuild kit we are willing to bet your seats are long overdue. It is no secret that the seats of the C5 & C6 have a reputation for being less than satisfactory in the area comfort and support. Over the last year or so, a solid repair process has been developed and we want to share it with everyone. We wanted to see how it worked out in my car for a year and can say I feel its 100% better than OEM. There are two problems: The side bolsters from the factory do not have any support under them. So as you climb in/out of the seat, the outside bolster foam tears where it sits on the steel seat frame and quickly sags or goes flat. The steel wires in the center area cut into the foam and quickly cause the foam to sag and pinching around the hip area. I found this extremely uncomfortable after only 15 minutes. This seat rebuild kit comes with all of the seat foam insert pieces necessary to provide the extra support needed to give your Corvette seats a more luxurious feel. If you want to improve the comfort of your Corvette without replacing the stock seats, this simple and affordable kit is a fantastic means by which you can do this. Easily installable at home, this kit provides the extra, high-density, strong and comfortable foam needed to give your Corvette seats extra support and cushion to help make your Corvette interior more luxurious and enjoyable. A great way to improve comfort and drivability quickly and affordably. This kit corrects a flaw in the original seat design that leads to premature failure of the center and bolsters. The kit includes: -Enough material to complete 1 seat -Upholstery grade high-density foam -Tough, wear-resistant ballistic nylon fabric -New, high quality, wire cover Jute Pad -Zip ties to replace the metal hog rings .25" thick high-density pad -Detail step-by-step photo instructions Working slowly, it takes about 1-2 hours. The detailed instructions with photos will take you thru it step by step. No special skill or tools required although you will need to purchase separately a can of spray glue for upholstery foam. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 Corvette
  • C6 Corvette Fan Control Switch

    C6 Corvette Fan Control Switch

    $99.95
    This brand new Plug-And-Play control module installs under the hood, at the fan connector, and is designed to manually control the PWM coolant fan found on the C6, Z06 and ZR1 Corvette. When the need arises to manually cool the radiator down, this module gives you complete control of the fan with the simple flick of a switch. This kit can be installed in less then one hour, once you decide on where you want to place the control switch. This switch matches the style and look of cockpit switches used on all the C6 Corvettes. Comes with easy to follow installation instructions. Pictures below are of completed installation with optional mounting bracket Installation instructions shown below... The switch wiring can be installed easily, without the need to cut a hole in the firewall. The wiring can be fed thru the upper door jamb, driver or passenger side, and hidden under the weatherstrip door seal into the passenger compartment. The location of the switch can be anywhere desired. First, locate the fan connector on the passenger side, near the bottom of the fan shroud. Unplug the connector and insert the enclosed module into the connection being sure the connectors are fully seated. The module can simply hang there on the connectors. You can now run the switch harness from the module to the passenger compartment location where you want the switch positioned. Start by plugging the round connector into the receptacle in the module. Next, select a location for the switch. You will need to cut a 20mm hole (approximately 11/16”) into the panel you wish to insert the switch. Once you have installed the switch, run the wiring from the harness and insert the three female connectors as shown in the switch wiring detail below. Note RED wire is common, BLACK wire is High, GREEN wire is Low, and RED wire is Common +12V: Once the switch wire connectors are attached, you are ready to go. Keep the switch in the center (O) “NORMAL” position for normal ECU fan control. Press the (I) to manually run the coolant fan on low, or the (II) to manually run it on high. Remember, manual control of the fan will make it run without the key in the ignition so be aware that you might kill your battery if left on for long periods of time. NOTE: There may be a coolant fan code set while the switch is in manual control, which will go away when switched back to normal mode. INSTALLING THE OPTIONAL SWITCHPLATE 1. There are Torx head screws holding on the lower panel directly under the C6 steering wheel. Remove the furthest right hand screw using a Torx T15 driver. 2. Route the fan control wiring to the right hand side of the foot well to the area near the switch plate mounting area. 3. Push the round fan control switch into the switch plate through the front of the plate and rotate the switch to adjust for the appropriate switch orientation. 4. Connect the wires as per the installation instructions. 5. Insert the Torx screw through the bottom of the switch plate and tighten until plate is secure. The hole is oversized so you can move and slightly wedge the switch plate behind the vent as seen inn the picture. This will make the switch plate more rigid. 6. Test the function of the switch and plate. Tighten the screw if necessary to secure the switch plate. Two finger operation of the switch may be necessary using your thumb and index finger. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • C5 C6 Corvette Jacking Pucks Pads

    C5 C6 Corvette Jacking Pucks Pads

    $41.99
    Free Shipping
    New and improved design that locks in place on all C5 and C6 Corvettes (including the Z06, ZR1, and Grand Sport). For all C5 and C6 Corvettes. Safely lift your Corvette in the air with our Corvette jacking pucks. The jacking pucks give you the ability to raise your car in the air without damaging your rocker panels. Our Corvette Jacking Pucks fit securely into your frame rails and will not shift or slide around as some traditional "hockey puck" style protectors do. They are very easy to install and remove, which give you the ability to safely raise your car without inflicting damage to your baby. Application: 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 CORVETTE
  • C6 Corvette Old School Mild to Wild Exhaust Control Switch Mild2Wild

    C6 Corvette Old School Mild to Wild Exhaust Control Switch Mild2Wild

    $49.99
    Free Shipping
    C6 Corvette Bi-Modal NPP Exhaust Control Foot Switch - Old School Pedal Mild to Wild This Mild to Wild switch allows for a true Old School style left-foot control switch for your very new C6 Corvette NPP bi-modal exhaust system. Just as other exhaust control switches do, this dead pedal Mild to Wild allows for control over your exhaust's quiet and loud modes as dictated by the vacuum valves. However, instead of putting that control at your fingertip, this Old School Mild to Wild puts that control at your feet. It's fun and exciting and really makes for a great "Wow" factor to just tap your foot and change your exhaust from quiet to loud. Installs in minutes: simply remove the OEM dead pedal (very easy, 2 nuts) and install this one. The special flat wire harness simply passes from the driver side to the passenger side and you then simply plug in the adapter into the fuse block. No ground wire to install.  Zero drain starts in the last setting you left it. No fob, no wireless, no visor. The heavy-duty switch is in simple reach, press loud, press quite, how simple. You can even switch it prior to starting the car. Perfect for all C6 Z06, ZR1, and NPP Equipped Corvettes. Application: 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette Z06, ZR1, Grand Sport
  • Corvette / Camaro Master Blaster Car Dryer

    Corvette / Camaro Master Blaster Car Dryer

    $439.99
    Free Shipping
    Drastically cut down on your car washing time and spend those extra hours enjoying your car on the road. The Metro Force Master Blaster Automotive and Motorcycle Dryer is the ultimate utility for washing your vehicle, and will help cut down on drying time and also provide an easier way for drying those hard to reach places on your car or motorcycle, such as: brake and side vents and vent inserts, engine panels and gaps, hood and trunk gaps, and window louvre recesses. Comes with Free Vacuum Wall Mount!  Flip the switch on your Air Force Master Blaster Car Dryer, and up to 58,500 ft./min. of rushing air is yours to aim. The twin 4 HP motors power dual-speed fans that dry your bike or auto in record time without a potentially damaging heating element.     Got a detail business? Even better. The Metro Air Force Master Blaster Car Dryer boasts durable all-steel construction that lasts. The 10 ft. commercial-grade hose and 12 ft. cord give you all the range you need. And, it weighs a mere 16 lbs. – powerful and portable. And, whether you use it for home or a business, your Metro Air Force Master Blaster Motorcycle Dryer carries a 1-year warranty. Features: The Metro Air Force Master Blaster Car & Motorcycle Dryer cuts your drying time by up to 75% Durable all-steel construction Dual motors producing 8HP at peak Blasts up to 58,500 ft. of air per minute Two-stage dual fan with two speeds Two temperature settings 10 ft. long x 1 1/2” diameter commercial-grade hose Topped by a heavy-duty neoprene blower nozzle 12 ft. heavy duty cord Weighs just 16 lbs. E/Z change foam filter Your Metro Air Force Master Blaster Motorcycle & Car Dryer carries a 1-year warranty   Since 1939, the Metropolitan Vacuum Cleaner Co., Inc. has evolved into a multidivisional corporation. From a small retail store front in the Bronx, NY rebuilding and selling vacuum cleaners, to a diversified multiunit manufacturing facility in 2001, producing amongst other products, Data-Vac Computer Cleaning Systems and Air Force Dog Dryers.   The early years for Metropolitan were solely devoted to vacuum cleaners. Founded by Israel and Pearl Stern, Metro was totally involved in the distribution and retailing of vacuum cleaners. From 1946 through 1949, the main core of Metro's business was the reconditioning and sale of vacuum cleaners to retail specialty stores, 5 & Dime and mail order houses.   In 1951 Jules Stern, son of Israel and Pearl, joined the business on a full-time basis. Between 1957 and 1970 Metro introduced three innovative industry "firsts". In 1957 a popularly priced 110-volt handheld vacuum cleaner. In 1964 the first 12-volt automotive hand held vacuum cleaner that plugged into the cigarette lighter outlet of cars. With the introduction of these two overwhelmingly successful products, demand outstripped production capabilities and a move to a larger facility was necessary. In 1968 Metro moved into its own 32,000 square foot building in Suffern, NY. In 1970 Metro introduced another industry first, the Metro Duo-Volt, the world's first and still only dual voltage (110V-12V) hand held vacuum cleaner, designed to work in the home and in the car.   In 1974 Kenneth Stern, the eldest son of Jules, joined Metro, adding a third generation of Sterns to the family business. Through the seventies and into the eighties Metro introduced many different models of vacuum cleaners from compact powerful canisters to full size vacuum cleaners.   In the eighties, Metro aggressively began to diversify into new and different industries. David Stern, Jules' youngest son, entered the company on a full-time basis in 1984. Since 1984 under the keen eyes of Jules, President, Kenneth, Vice-President of National Sales and David, Vice-President of Marketing, many new and different markets have been opened for Metro products.   Metro is now a major factor in the computer/office product industry with Metro Data-Vac Computer Cleaning Systems. Data-Vac Computer Cleaning Systems are designed to avoid costly downtime. Ever so important, is the cleanup and maintenance of computers, printers, laser printers and copiers.   2001 proved to be extraordinary for Metro for a number of reasons, Continuous growth of the Data Vac division, Metro's Magic Air Division which markets high volume pumps and inflator/deflators to the marine, camping and sporting goods industries and Metro's Air force Pet Grooming Dryers Division which by January of 1989, was catapulted to the top of the pet dryer industry and now has over 80 wholesale distributors in the United States and many foreign countries. Metro is concentrating on expanding all of these diverse product categories with the introduction of new products in each of their divisions.   Metro entered the motorcycle industry in April, 2002, with the Air Force Blaster Motorcycle Dryer. The Metro Air Force Blaster motorcycle dryer was specifically designed for cleaning and drying motorcycles with dry, filtered warm air (about 20-25 degrees above ambient temperature). The Metro Air Force Blaster will cut cleaning time by 80%. Five to seven minutes is all it takes to quickly and effectively dry motorcycles. The Blaster is the hottest new motorcycle care product to come out in decades and is completely safe for all paint and chrome finishes. In our 65 years of business, this has been one for the fastest and most successful product launches ever.   The above information has been provided by the Manufacturer and AutoAnything cannot guarantee the accuracy thereof or endorse the opinions expressed.   The Master Blaster Car Dryer is a portable, high-speed air dryer designed specifically for drying cars, trucks, and other vehicles. The dryer uses a powerful air stream to blow water off of the surface of the vehicle, helping to prevent water spots and streaks from forming.One of the standout features of the Master Blaster Car Dryer is its high-speed motor, which delivers an airflow of up to 140 mph. This powerful airflow helps to quickly and effectively dry the surface of the vehicle, reducing the risk of water spots and streaks. The dryer also has an adjustable airflow control, which allows users to adjust the speed of the air stream to suit the needs of their vehicle.In addition to its drying capabilities, the Master Blaster Car Dryer is also designed to be portable and easy to use. The dryer has a lightweight, compact design and comes with a number of accessories, such as a flexible hose and various nozzles, to help users reach all areas of the vehicle. The dryer is also equipped with a long power cord, which allows users to easily reach all areas of the vehicle without having to move the dryer itself. Overall, the Master Blaster Car Dryer is a useful tool for anyone who wants to quickly and effectively dry their car, truck, or other vehicle. Its high-speed motor and adjustable airflow control make it an effective tool for preventing water spots and streaks, and its portable design makes it easy to use.
  • C5-C6 Corvette O2 Sensor Wiring Extension Square Plug

    C5-C6 Corvette O2 Sensor Wiring Extension Square Plug

    $25.95
    When installing aftermarket headers and cat-back systems in your vehicle, the oxygen sensor is frequently relocated, usually far enough away from the original wiring location that the connector cant be re-installed. You cannot cut and splice oxygen sensor wiring since this can permanently damage the sensor and considerably reduce the accuracy of the signal. These harness extensions are "Plug-And-Play" and utilize OEM connectors, terminals and seals with OEM wiring to maintain precisely accurate signals and safely extend the wiring connections. Note: Please check your connector shape and color to see if it matches your application. Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 Corvette Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • C6 Corvette O2 Extension C6 Corvette

    C6 Corvette O2 Sensor Extension

    $27.49
    When installing aftermarket headers and cat-back systems in your vehicle, the oxygen sensor is frequently relocated, usually far enough away from the original wiring location that the connector cant be re-installed. You cannot cut and splice oxygen sensor wiring since this can permanently damage the sensor and considerably reduce the accuracy of the signal. These extensions are "Plug-And-Play" and utilize OEM connectors, terminals and seals with OEM wiring to maintain precisely accurate signals and safely extend the wiring connections. Note: Please check your connector shape and color to see if it matches your application. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • C6 Corvette /Camaro O2 Sensor Extension

    C6 Corvette /Camaro O2 Sensor Extension

    $25.95
    When installing aftermarket headers and cat-back systems in your vehicle, the oxygen sensor is frequently relocated, usually far enough away from the original wiring location that the connector cant be re-installed. You cannot cut and splice oxygen sensor wiring since this can permanently damage the sensor and considerably reduce accuracy of the signal. These extensions are "Plug-And-Play" and utilize OEM connectors, terminals and seals with OEM wiring to maintain precisely accurate signals and safely extend the wiring connections. Note: Please check your connector shape and color to see if it matches your application.
  • C6 Corvette RTD Sim C6 Corvette

    C6 Corvette Real Time Dampening Simulators

    $179.99
    Free Shipping
    ELIMINATED MIL LIGHT AND ASSOCIATED CODES WHEN REPLACING FACTORY SHOCK ABSORBERS. The active suspension F55 RTD (Real Time Dampening) is an awesome option for the C6 Corvette. Soft while cruising down the street and then it firms when you really want to enjoy the handling your Corvette was designed for. But suspension technology has come a long way since your C6 Corvette rolled out from the factory or you are upgrading your car for more track orientated performance. But you then discover when replacing your factory dampening shocks just how much replacements cost. You are "shocked" when you discovered that the cost of ONE factory shock could enable you to replace ALL FOUR shocks with the best aftermarket shocks! If you do this, however, the MIL (Malfunction Indicator Light) turns on and the car's top speed is limited to 80 MPH! By using our kit, you can then choose any shock absorber or coil over suspension that suits your needs, and turn the MIL codes off, restoring the car to its original performance. Our Real Time Dampening Simulators Kit consists of eight modules, two for each wheel location. Simple "Plug-And-Play" installation takes only a few minutes and requires no cutting to your factory harness. Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • C6 Corvette  LS2/LS7 Throttle Body (ETC) Extension - 24"

    C6 Corvette LS2/LS7 Throttle Body (ETC) Extension - 24"

    $47.95
    If you are looking to tap into the LS2 / LS7 Electronic Throttle Control cable for nitrous, supercharger or turbo upgrades to your Corvette that require you to cut the OEM wires and lengthen this connector but you do not want to hack up your factory harness. Well, you will not have to cut any longer! CASPER'S ELECTRONICS proudly announces the availability of the GT 6 Way throttle cable mate connector. This connector is built to OEM specification materials rated for underhood connections. Completely plug-and-play connections!  Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette
  • C5-C6 Corvette 24" O2 Sensor Extension Harness

    C5-C6 Corvette 24" O2 Sensor Extension Harness

    $26.95
    When installing aftermarket headers and cat-back systems in your vehicle, the oxygen sensor is frequently relocated, usually far enough away from the original wiring location that the connector cant be re-installed. You cannot cut and splice oxygen sensor wiring since this can permanently damage the sensor and considerably reduce the accuracy of the signal. These extensions are "Plug-And-Play" and utilize OEM connectors, terminals and seals with OEM wiring to maintain precisely accurate signals and safely extend the wiring connections. Note: Please check your connector shape and color to see if it matches your application. Sold individually, some applications require two Application: 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 C6 Corvette Application: 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004 C5 Corvette
  • C5 C6 1997-2013 Corvette Fuel Pump Hotwire Wiring Kit

    C5 C6 1997-2013 Corvette Fuel Pump Hotwire Wiring Kit

    $71.95
    This C5 C6 1997-2013 Corvette Fuel Pump Hotwire Wiring Kit from CEI and offered by Southern Car Parts is designed to install into your C5 or C6 Corvette to overcome the losses associated with your factory wiring harness to the fuel pump. Because of the heavy 12 gauge feed, sealed relay and attachment to the output stud of the alternator, extra voltage and current become available to the fuel pump, increasing both fuel volume and pressure during WOT, when it is needed most. Southern Car Parts has everything you need to make sure your C5 or C6 Corvette looks great and keeps running strong. Aftermarket Pumps will not work with this wiring kit Application: C5 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, C6 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 Corvette
  • C6 2005-2013 Corvette Z06 MAF/IAT Breakout Harness

    C6 2005-2013 Corvette Z06 MAF/IAT Breakout Harness

    $29.95
    Free your IAT from the heat with Caspers Electronics MAF/IAT breakout harness. These easy-to-install harnesses move your IAT sensor to a cooler location for a more accurate temperature reading and improved drivability. Relocate your IAT with Caspers Electronics breakout harnesses.This is the WIDE GT connector. This connector is found on the G8, Modular MAF Corvette (such as the C6 Z06). Application: C6 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013 Z06 Corvette
  • Genius Battery Charger 12V Lighter Plug Connector

    Genius Battery Charger 12V Lighter Plug Connector

    $28.99
    Fits G750-G3500 The GC003 12V Plug Connector works with NOCO Genius battery chargers and allows the battery chargers to charge and maintain your vehicle's battery by simply plugging into the 12V auxiliary plug/cigarette lighter. The Quick Connect cable makes connecting the 12V Plug Connector simple. Ideal for motorcycles where the battery compartment is difficult to access. This 12V Plug Connector allows for the easiest and most time effective way of hooking up and unhooking your NOCO Genius Battery Charger to any vehicle you may have. Works with all standard 12V Cigarette Lighters. Does not change Genius Battery Charger functionality in any way.

25 Item(s)

Grid List

Set Descending Direction

Corvette DiabloSport Tuner

One of the most surefire ways to unlock more out of your engine's potential is to reprogram the engine with an electronic tuner. Corvette tuners can both help realize greater potential from the stock engine, as well as provide more horsepower and performance from every other aftermarket modification component installed. A DiabloSport Corvette tuner, or other electronic Corvette tuner, allows for customization of the driver experience with multiple tunes--each specifically designed to highlight certain engine performance efficiency aspects in different driving locations and requirements. Coupling custom tunes with your Corvette, and the ability to switch between your Corvette tunes with relative ease offered by these modern electronic Corvette tuners, allows for the Corvette driver to fine tune their driving experience to their driver needs and get more from their vehicle than ever before.

Corvette Jacking Pucks

Other smaller component modifications, the miscellany of the Corvette experience, can go a long way to improving a Corvette driver's feeling of connection and customization. Visual Corvette mods, stylistic Corvette mods, Corvette exhaust control mods, and comfort Corvette mods are clearly of equivalent importance as performance Corvette modifications for many drivers. Corvette battery tenders, upgraded Corvette oxygen sensors, Corvette jacking pucks, and Corvette fan control switches--as well as other Corvette component products--can also help extend the life of the vehicle beyond its already expected many years of performance and service. We're proud to offer a full catalog of aftermarket Corvette modification pieces, both for Corvette performance and Corvette customization, that each and every driver can find both a use and need for in their specific situation. These parts come together to complete are extensive Corvette parts catalog with high quality pieces at incredible pricing.

Corvette C6 Tuners-Miscellaneous

Minimal Price: $ 17.95 17.95

X